Real factory photos in sequence: hover over the image (or drag on your phone) to see the equipment from every angle.
Dalla Belt Conveyor
The Dalla Belt Conveyor speeds up loading and unloading at the truck, cutting labor costs and increasing productivity.
Applications
6 models available as standard, plus custom adaptations when your layout calls for them.
About the Dalla Belt Conveyor
The Dalla Belt Conveyor speeds up loading and unloading at the truck, cutting labor costs and increasing productivity.
It is built with 1020 carbon steel bars, in a strong, sturdy structure that is easy to move. It has an enclosed gearmotor for the drive and a rubber belt that comes in several types according to each application: tractor-tire tread, pyramid or V cleats to convey the products.
It has a belt reversing system that allows the conveyor to be used for loading or unloading, and automotive wheels and tires that let you move the equipment quickly anywhere. The conveyor height can be adjusted automatically with the electric switch or manually with a ratchet crank, turning what used to take hours into just a few minutes.
Technical features
- 13″ automotive wheels and tires
- Rubber belt with tractor-tire tread
- Reversing system for loading and unloading
- Electric lift or manual crank lift
- Main structure built with rectangular tubes
- Equipped with cage-type drive pulley
- Galvanized belt support rollers with bearings
- Adjustment with bearings for belt alignment
- Ø5″ swivel casters at the rear
- Enclosed gearmotors
- Available in 220, 380 or 440 volts three-phase; in special cases the motor can be single-phase
- Mostly PU (polyurethane) paint, in blue
Specifications
Compare the 6 models
Factory reference values. Length, belt width and drive can be adjusted according to the project.
Same on every model
- Belt width
- 0,5 m
- Speed
- 40 m/min
- Capacity
- 70 kg/m
ETD3
- Length
- 3 m
- Maximum height
- 1,8 m
- Minimum height
- 1 m
- Drive motor
- 0,75 cv
ETD5
- Length
- 5 m
- Maximum height
- 3 m
- Minimum height
- 1,2 m
- Drive motor
- 1 cv
ETD6
- Length
- 6 m
- Maximum height
- 3,6 m
- Minimum height
- 1,2 m
- Drive motor
- 1,5 cv
ETD8
- Length
- 8 m
- Maximum height
- 5 m
- Minimum height
- 1,3 m
- Drive motor
- 2 cv
ETD10
- Length
- 10 m
- Maximum height
- 6 m
- Minimum height
- 1,3 m
- Drive motor
- 3 cv
ETD12
- Length
- 12 m
- Maximum height
- 7,2 m
- Minimum height
- 1,3 m
- Drive motor
- 3 cv
Engineering tools
Do the math before requesting a quote
The same logic our engineering team uses every day, with the models from our real production table.
Adjust length and incline and see the drawing.
Schematic drawing at approximate scale, just for you to see how it fits in the layout.
Model
ETD8
Discharge height
3.0 m
Motor
2 cv
Belt
Cleated belt
Compatibility
Which material this equipment is for
A quick guide by type of load. "On request" does not mean no: it means it can be done with an adjustment of belt, profile, sealing or structural material, which is why we need to know your product before recommending.
- Grain and bulkOn request
- BagsRecommended
- Boxes and packagesRecommended
- Waste and recyclingOn request
- Sand and gravelOn request
- CharcoalOn request
- Fruits and vegetablesOn request
Your material is not on the list? Describe it on WhatsApp and we will tell you right away whether this line fits or which equipment is the right one.
Maintenance checklist
Checklist for the Dalla Belt Conveyor
Routine from the Dalla conveyor's technical manual. The point that causes most trouble when forgotten is belt alignment.
0 of 11 items
Every month
- Lubricate the bearings through the grease fittings on the housings, with standard grease
- Check belt alignment: its edges should follow the edges of the drive pulley and the tail pulley
See the manual for further information.
Periodically
- Clean and lubricate with standard grease the swivel casters on the feet, when fitted
- Watch the bearings: loud noise, vibration, heating or abnormal wear
- Keep the motor clean, with the ventilation free for the fan air to circulate
- Check the electrical connections and the motor mounting bolts
- Gearbox: it comes from the factory with synthetic oil, which needs little maintenance; keep it clean and inspected
See the manual for further information.
If the belt runs off
- Remove the side guards and loosen the pulley nuts
- Turn the tensioning screw half a turn clockwise on the side the belt is rubbing
- Wait for the belt to make a full turn and observe; repeat until aligned
- Make the adjustment on the drive and driven pulleys, retighten and refit the guards
See the manual for further information.
Always
- Start the conveyor empty and do not leave it running without material for long periods, because that increases wear
- At the end of the shift, leave it running until all the material has been discharged
Installation sheet
What to have ready before the machine arrives
When the site is prepared, the machine goes into operation on the day it arrives. This is the list we give customers when the order is closed.
- 1Space and headroomCheck the total length with the structure and the area to work around it, as well as the headroom up to the roof, beam or piping at the discharge point.
- 2Firm, level floorA flat, firm base under the support feet. An uneven floor misaligns the belt and makes the structure work twisted.
- 3Power point at the correct voltageHave the power point ready at the voltage stated in the order, with circuit breaker and grounding. Tell us whether the supply is three-phase before the motor is built.
- 4Access for unloadingCheck the gate, aisle and ceiling height on the truck's way to the assembly point. Long equipment may arrive in parts.
- 5Defined infeed and discharge pointsMark where the product enters and where it falls. Hopper, feed table or discharge spout must be planned before fixing the equipment.
What makes thismachine lastfull shifts
Tap the points on the photo to see what is behind each detail of the design.
- 13″ automotive wheels and tires
- Rubber belt with tractor-tire tread
- Reversing system for loading and unloading
- Electric lift or manual crank lift
Before you buy
3 mistakes that cost dearly in this choice
These are the mismatches we see most in machines bought in a hurry. It costs little to check beforehand and a lot to fix afterwards.
Undersized belt width
Choosing the belt by price and not by load makes the product overflow at the sides and turns the line into constant cleaning. Size it by the largest item that will pass and by the peak volume, not by the daily average.
Motor working at its limit
An undersized motor heats up, trips in the middle of the shift and takes the gearbox with it. It pays to leave spare motor capacity, especially uphill, with a full load and frequent starts.
Wrong belt for the material
A smooth belt on a steep incline with loose material sends the load back to the foot of the conveyor. Loose material on an incline calls for cleats; fine bulk performs better on a V profile; a food line calls for a non-toxic belt.
After-sales
Spare parts and consumables
Wear items we supply for this line. Having the critical parts in stock before harvest is what separates a stoppage of hours from a stoppage of days.
Need a part now?
Tell us the equipment and, if you have it, send a photo of the part. The quote comes straight from technical service.
Frequently asked questions
What people ask most about this equipment line.
See all frequently asked questions →Yes. Length, belt width, incline and discharge height are adjusted in the project to fit your layout.
We build stainless steel and galvanized versions, with a belt suited to sanitation. Tell us the type of cleaning used at your plant.
It depends on the material, the load per hour and the cleaning. A belt that is well tensioned, aligned and with a working scraper lasts much longer. We keep belts and splices as spare parts.
By WhatsApp, phone, e-mail or any form on the website. To speed things up, tell us the material conveyed, the distance to cover, the discharge height and the capacity you want. If you can send a photo or video of the site, the sizing will be more accurate.
Nothing leaves the factory without a running test. Larger equipment may arrive in parts for transport and is assembled on site following the guidance we send along.
Quote
Request a proposal for the Dalla Belt Conveyor
To speed things up, tell us: material conveyed, length needed, discharge height and capacity wanted. If you have photos of the site, even better: send them on WhatsApp.
- Project sized for your operation
- Manufactured in-house in Limeira/SP, Brazil
- Delivery throughout Brazil
- Technical service and spare parts
Related equipment
Need custom-built equipment?
Send us the details of your operation: material, length, height and capacity. Our engineering team puts together the ideal solution and you get the quote within 1 business day.
(19) 3033-9397 · (19) 99884-2717 · vendas@demakine.com.br